| |
|
| Anti corrosive Resins |
|
 |
|
Chemifix BIPA |
|
|
|
Chemifix BIPR |
|
|
|
Chemifix CFR |
|
|
|
|
Anti corrosive Powders |
|
|
|
Chemifix SSP |
|
|
|
Chemifix KSP |
|
|
|
Chemifix PHP |
|
|
|
Chemifix FP |
|
|
|
Chemifix CNP |
|
|
|
Chemifix SUP |
|
|
|
Chemifix Q10 |
|
|
|
Chemifix CFP |
|
|
| Anti Corrosive Bitumen Mastic |
|
|
|
Chemifix SBM |
|
|
|
Chemifix HDBM |
|
|
|
Chemifix TRBM |
|
|
|
Chemifix SPBM |
|
|
|
Chemifix HFBM |
|
|
|
|
|
|
 |
|
| |
| |
|
|
|
Chemifix CNSL. (Cashew Nut Shell Liquid) resin Cement consists of an inert powder Chemifix CNP (Power) which is mixed with a synthetic resin Chemifix CNR (Resin), to produce a mortar Chemifix CNSL, which is resistant to most Alkaline conditions. It is not resistant to certain solvents, oils, chlore compounds and aromatics. Chemifix CNSL is more flexible than other acid resistant cements. |
|
In addition to this, Chemifix CNSL. combines optimum working life with minimum hardening time. |
|
Chemifix CNSL. can economically solve the majority of corrosion problems. it is one of the most widely used corrosion proof cement in the country.
|
|
|
Physical Data : |
|
|
|
| |
Tensile strength |
: |
200-300 lb per sq. in |
|
| |
Temperature limit |
: |
190ºC |
|
| |
Porosity (Max.%) |
: |
0I |
|
| |
Mixing ratio: C.N.S.L. |
: |
1Power: Syrup 3:1 by weight |
|
| |
Adhesion to unglazed (kg/cm2) |
: |
10 |
|
| |
ceramic ware Shelf life |
: |
Syrup : 3 months if kept cool, dry and containers sealed. |
|
| |
|
: |
Powder : Should be used as fresh as possible. |
|
|
|
Application Area |
|
Chemifix CNSL. is widely used for bonding or pointing of bricks/tiles for anti-corrosive constructional work areas like tanks, Channels, Floors, Foundations, Pits, etc. |
|
| Application Method |
|
Chemifix CNP (Powder) and Chemifix CNR (Resim) are to be mixed in the ratio of 3:1 PBW veru carefully in a clean, enamelled bowl, Mixing should be done by adding powder to Resin in small quantities. The CNSL mortar produced should be used up within 20 minutes from mixing. Some heat will be produced in the setting of CNSL mortar; so it is important to spread the mixed CNSL mortar in a thin layer. The hardening time will take upto 2 to 3 hours when the conditions are warm. |
|
|
|
|
All surfaces to which Chemifix CNSL mortar is to be applied must be dry, clean and rust free. No water, steam or acid should be allowed to come in contact with the mortar during setting and hardening. |
|
|
|
Chemifix CNSL should not be applied directly to concrete surface or steel surface. |
|
|
|
Depending upon the chemical and operating conditions as well as the base structure (Concrete or steel) suitable non-porous Membrane / Inter-liner should be provided. Some of the suggested inter protective layers are Mastic, Rubber, FRP, Epoxy/Synthetic Screeds and FlexyVinyl Sheet (PVC). Membrane should be provided as per standard recommendations. |
|
|
|
Mixing ratio can be adjusted to about 10% according to site conditions. |
|
|
|
Always prepare that much quantity which can be consumed within the working time at the prevailing site condition. |
|
|
|
Apply prepared mortar to the backside of thetile/brick. The bedding thickness will be about 6mm. Place the tile/brick on inter protective liner applied on concerete surface and press it firmly, so that the bedding is uniform. |
|
|
|
Maintain required joint width using spacer blocks. |
|
|
|
Surplus material should carefully scraped off with a trowel.. |
|
|
|
|
|
| |
powered
by |
Ultra InfoTech |
powered
© 2000 - 2008 All Right Reserved - Chemisight |
|
|
|
