| |
|
| Anti corrosive Resins |
|
 |
|
Chemifix BIPA |
|
|
|
Chemifix BIPR |
|
|
|
Chemifix CFR |
|
|
|
|
Anti corrosive Powders |
|
|
|
Chemifix SSP |
|
|
|
Chemifix KSP |
|
|
|
Chemifix PHP |
|
|
|
Chemifix FP |
|
|
|
Chemifix CNP |
|
|
|
Chemifix SUP |
|
|
|
Chemifix Q10 |
|
|
|
Chemifix CFP |
|
|
| Anti Corrosive Bitumen Mastic |
|
|
|
Chemifix SBM |
|
|
|
Chemifix HDBM |
|
|
|
Chemifix TRBM |
|
|
|
Chemifix SPBM |
|
|
|
Chemifix SPBM |
|
|
|
|
|
|
 |
|
| |
| |
|
|
|
Chemifix F (Furan Resin Mortar): This Cement is a two component system. Furan Power (Chemifix FP) and Furan Resin (Chemifix FR). The Chemifix F mortat is a formulation of Siliceous fillers mixed with a powder catalyst to provide desired charateristics like good chemical resistance, mechanical strength and low porosity. Chemifix F is resistant to all non-oxidisting acids. Solvents, Salts, Greases, Alkalies and Detergents. In addition to the, Chemifix F combines optimum working life with minimum hardening time. |
|
ChemifixF can economically solve the majority of corrosion problems. it is one of the most widely used corrosion proof cement in the country.
|
|
|
Physical Data : |
|
|
|
| |
Tensile strength |
: |
500 - 700 lb per. sq. to |
|
| |
Temperature limit |
: |
170ºC |
|
| |
Porosity (Max. %) |
: |
0I |
|
| |
Mixing ratio |
: |
Powder/syrup 3:1 by weight |
|
| |
Bond strength Minimum, Kg/cm2 (at 14 days) |
: |
05 |
|
| |
Adhesive to unglazed ceramic were (kg /cm) |
: |
16 |
|
|
| Application Area |
|
Chemifix F is widely used for bonding or pointing of bricks/tiles for anti-corrosive constructional work areas like tanks, Channels, Floors, Foundations, Pits, Effluent treatment pickling tanks, Drains, Chimneys, Reactions Tanks and other areas where corrosives like Nitric Acid are handled. |
|
| Application Method |
|
Chemifix FP (Powder) and Chemifix FR (Resin) are to be mixedom the ratio of 3:1 PBW very carefully in a clean, enamelled bowl, Mixing should be done by adding powder to Resin in small quantities. The Furan mortar (Chemifix F) produced should be used up withing 20 minutes from mixing. Some heat will be produced in the setting of Furan mortar, so it is important to spread the mixed Furan mortar in a thin layer. The hardening time will take upto 2 to 3 hours when the conditions are warm. |
|
|
|
|
All surfaces to which Chemifix F mortar is to be applied must be dry, clean and rust free. No water, steam or acid should be allowed to come in contact with the mortar during setting and hardening. |
|
|
|
Chemifix F should not be applied directly to concrete surface or steel surface. |
|
|
|
Depending upon the chemical and operating conditions as well as the base structure (Concrete or steel) suitable non-porous Membrane / Inter-liner should be provided. Some of the suggested inter protective layers are Mastic, Rubber, FRP, Epoxy/Synthetic Screeds and FlexyVinyl Sheet (PVC). Membrane should be provided as per standard recommendations. |
|
|
|
Mixing ratio can be adjusted to about 10% according to site conditions. |
|
|
|
Always prepare that much quantity which can be consumed within the working time at the prevailing site condition. |
|
|
|
Apply prepared mortar to the backside of the tile/brick. The bedding thickness will be about 6mm. Place the tile/brick on inter protective liner applied on concerete surface and press it firmly, so that the bedding is uniform. |
|
|
|
Maintain required joint width using spacer blocks. |
|
|
|
Surplus material should carefully scraped off with a trowel.. |
|
|
|
|
|
| |
powered
by |
Ultra InfoTech |
powered
© 2000 - 2008 All Right Reserved - Chemisight |
|
|
|
