| |
|
| Anti corrosive Resins |
|
 |
|
Chemifix BIPA |
|
|
|
Chemifix BIPR |
|
|
|
Chemifix CFR |
|
|
|
|
Anti corrosive Powders |
|
|
|
Chemifix SSP |
|
|
|
Chemifix KSP |
|
|
|
Chemifix PHP |
|
|
|
Chemifix FP |
|
|
|
Chemifix CNP |
|
|
|
Chemifix SUP |
|
|
|
Chemifix Q10 |
|
|
|
Chemifix CFP |
|
|
| Anti Corrosive Bitumen Mastic |
|
|
|
Chemifix SBM |
|
|
|
Chemifix HDBM |
|
|
|
Chemifix TRBM |
|
|
|
Chemifix SPBM |
|
|
|
Chemifix SPBM |
|
|
|
|
|
|
 |
|
| |
| |
|
|
|
Chemifix PH. is carbon and silica filled Phenolic Resin Cement which resists all concentrations of non-oxidising acids; acidic salts and organic solvents. It is especially formulated to resist acidic, alkaline and also mixed acidic and alkaline conditions, Chemifix PH cements's most outstanding property is its remarkable resistance to Sulphuric acid both dilute & concentrated. Even concentrations upto 93% at room temperature will not attack Chemifix PH |
|
Chemifix PH coonsists of an inert powder Chemifix PH (Powder) which is mixed with a Phenolic synthetic resin Chemifix PH (Resin), to produce a mortar,
Chemifix PH, which is used to bond acid resisting bricks/tiles for anti-corrosive contructional work. Chemifix PH combines optimum working life with minimum hardening time. |
|
Chemifix PH. can economically solve the majority of corrosion problems. it is one of the most widely used corrosion proof cement in the country.
|
|
|
Physical Data : |
|
|
|
| |
Tensile strength |
: |
600-700 lb per sq. in |
|
| |
Compressive Strength |
: |
350 (kg/cm²) |
|
| |
Temperature limit |
: |
170ºC |
|
| |
Water Absorption (Max. %) |
: |
0I |
|
| |
Mixing ratio |
: |
Power/ Syrup -3:1 by wt |
|
| |
Adhesion to unglazed |
: |
100-200 lb. per sq. in. Phenolic Syrup should be stored in cold storage |
|
| |
ceramic ware Shelf life |
: |
at about 27ºC and used as early as possible preferably within 15 days |
|
| |
|
: |
Phenolic powder should be used be used as early as possible and preferably withing 45 days. |
|
|
| Application Area |
|
Chemifix PH. is widely used for bonding or pointing of bricks/tiles for anti-corrosive constructional work areas like tanks, Channels, Floors, Foundations, Pits, etc. |
|
| Application Method |
|
Chemifix PHP (Powder) and Chemifix PHR (Resin) are to be mixedom the ratop pf 3:1 PBW veru carefully in a clean, enamelled bowl, Mixing should be done by adding powder to Resin in small quantities. The Phenolic mortar (Chemifix PHP) produced should be used up withing 20 minutes from mixing. Some heat will be produced in the setting Phenolic mortar, so it is important to spread the mixed Phenolic mortar in a thin layer.The hardening time will take upto 2 to 3 hours when the conditions are warm. |
|
|
|
|
All surfaces to which Chemifix PH mortar is to be applied must be dry, clean and rust free. No water, steam or acid should be allowed to come in contact with the mortar during setting and hardening. |
|
|
|
Chemifix PH should not applied directly to concrete surface or steel surface. |
|
|
|
Depending upon the chemical and operating conditions as well as the base structure (Concrete or steel) suitable non-porous Membrane / Inter-liner should be provided. Some of the suggested inter protective layers are Mastic, Rubber, FRP, Epoxy/Synthetic Screeds and FlexyVinyl Sheet (PVC). Membrane should be provided as per standard recommendations. |
|
|
|
Mixing ratio can be adjusted to about 10% according to site conditions. |
|
|
|
Always prepare that much quantity which can be consumed within the working time at the prevailing site condition. |
|
|
|
Apply prepared mortar to the backside of the tile/brick. The bedding thickness will be about 6mm. Place the tile/brick on inter protective liner applied on concerete surface and press it firmly, so that the bedding is uniform. |
|
|
|
Maintain required joint width using spacer blocks. |
|
|
|
Surplus material should carefully scraped off with a trowel.. |
|
|
|
|
|
| |
powered
by |
Ultra InfoTech |
powered
© 2000 - 2008 All Right Reserved - Chemisight |
|
|
|
