| |
|
| Anti corrosive Resins |
|
 |
|
Chemifix BIPA |
|
|
|
Chemifix BIPR |
|
|
|
Chemifix CFR |
|
|
|
|
Anti corrosive Powders |
|
|
|
Chemifix SSP |
|
|
|
Chemifix KSP |
|
|
|
Chemifix PHP |
|
|
|
Chemifix FP |
|
|
|
Chemifix CNP |
|
|
|
Chemifix SUP |
|
|
|
Chemifix Q10 |
|
|
|
Chemifix CFP |
|
|
| Anti Corrosive Bitumen Mastic |
|
|
|
Chemifix SBM |
|
|
|
Chemifix HDBM |
|
|
|
Chemifix TRBM |
|
|
|
Chemifix SPBM |
|
|
|
Chemifix SPBM |
|
|
|
|
|
|
 |
|
| |
| |
 |
|
(Sodium Silicate) Mortar |
|
|
|
Chemifix SS (K. Silicate Resin Mortat): This Cement is a two component system. Sodium Silicate Power (Chemifix SSP) and Sodium Silicate Resin (Chemifix SSR). The Chemifix SS mortat is a formulation of Siliceous fillers mixed with a powder catalyst to provide desired charateristics like good chemical resistance, mechanical strength and low porosity. In addition to this, Chemifix SS combines optimum working, life minimum hardening time. It is the only cement mortar, apart from Chemifix KS, wich can resist Nitric Acid. It can even resist Oleum and fumng Sulphuric Acid.This Cement is not resistant to Akalies. |
|
Chemifix SS can economically solve the majority of corrosion problems. it is one of the most widely used corrosion proof cement in the country.
|
|
|
Physical Data : |
|
|
|
| |
For the mixed mortarcontaining 3 parts by weight of Ssi Powder and 1 Part by weight of Ssi solution. |
|
| |
Working time, Minimum at 27 + 20C (Minutes) |
: |
20 |
|
| |
Flexural strength, Minimum, Kg/cm² (at 7 days) |
: |
45 |
|
| |
Compressive strength, Minimum Kg/cm² (at 7 days) |
: |
150 |
|
| |
Bond strength Minimum, Kg/cm² (at 14 days) |
: |
5 |
|
| |
Absorption of toluene, Maximum percenby wight |
: |
18 |
|
| |
Maximum service temperature (dry air) |
: |
650ºC |
|
| |
Note: Properties 1 to 5 tested as per IS : 4456 (part 1) -1967. |
|
|
| Application Area |
|
Chemifix SS is widely used for bonding or pointing of bricks/tiles for anti-corrosive constructional work areas like tanks, Channels, Floors, Foundations, Pits, Effluent treatment pickling tanks, Drains, Chimneys, Reactions Tanks and other areas where corrosives like Nitric Acid are handled. Chemifix SS has higher temperature limitations, so it is widely used in the construction of Chimneys, Roasters and other and other high temperature equipments. |
|
| Application Method |
|
Chemifix SSP (Powder) and Chemifix SSR (Resin) are to be mixed in the ratio of 3:1 PBW very carefully in a clean, enamelled bowl, Mixing should be done by adding powder to Resin in small quantities. The Furan mortar produced should be used up withing 20 minutes from mixing. Some heat will be produced in the setting of Furan mortar, so it is important to spread the mixed Furan mortar in a thin layer. The hardening time will take upto 2 to 3 hours when the conditions are warm. |
|
|
|
|
All surfaces to which Chemifix SS mortar is to be applied must be dry, clean and rust free. No water, steam or acid should be allowed to come in contact with the mortar during setting and hardening. |
|
|
|
Chemifix SS should not be applied directly to concrete surface or steel surface. |
|
|
|
Depending upon the chemical and operating conditions as well as the base structure (Concrete or steel) suitable non-porous Membrane / Inter-liner should be provided. Some of the suggested inter protective layers are Mastic, Rubber, FRP, Epoxy/Synthetic Screeds and FlexyVinyl Sheet (PVC). Membrane should be provided as per standard recommendations. |
|
|
|
Mixing ratio can be adjusted to about 10% according to site conditions. |
|
|
|
Always prepare that much quantity which can be consumed within the working time at the prevailing site condition. |
|
|
|
Apply prepared mortar to the backside of the tile/brick. The bedding thickness will be about 6mm. Place the tile/brick on inter protective liner applied on concerete surface and press it firmly, so that the bedding is uniform. |
|
|
|
Maintain required joint width using spacer blocks. |
|
|
|
Surplus material should carefully scraped off with a trowel.. |
|
|
|
|
|
| |
powered
by |
Ultra InfoTech |
powered
© 2000 - 2008 All Right Reserved - Chemisight |
|
|
|
